Friday, April 30, 2010

New conical wheel rebuild part 1


I've decided that to be a truely great bike builder (someday) I should really know how to build and lace wheels. The front wheel on my BSA is rough, but I don't want to take it off and lose riding time. This wheel came from oley for $40. Looks rough? Yup. I am going to make this into a beauty.....

Uploaded by www.cellspin.net

Saturday, April 24, 2010

Oley 2010 highlights


Just checked out the Oley Swap meet this weekend. I picked up a few spares for the Thunderbolt (new front wheel, airbox covers, new handlebar switches). Check out Smoke and Throttle for complete set of pictures.

Wednesday, April 21, 2010

Lots of spacers correct pipe balance


As you can see I put a bunch of washers to (almost) correct the misaligned pipe stays. They need a few more spacers which I'll eventually replace with solid spacers and the right size bolt. Kind of a bummer that I spent so much on these pipes and they're crooked.

Uploaded by www.cellspin.net

Saturday, April 17, 2010

Chadds Ford Moto-Auction


Just Checked out the goods. See my post on Smoke and Throttle for details!!!!

Thursday, April 15, 2010

Pipes still don't line up at cross section


The first set of headers I ordered wouldn't fit at the cross section. I thought it was the left header being welded wrong. I exchanged it and the new ones are the same deal. My original left header was cracked at the cross fitting. Is it my exhaust ports?

Uploaded by www.cellspin.net


Monday, March 29, 2010

Pulling Dents from my 4 gal. tank

Last Saturday I decided that, while Bondo works ok, pulling dents from tanks is probably better - so I went out and purchased a stud welder from a local auto-body supply.
$200 later, I was the proud owner of a 110V stud welder. This little baby welds studs right onto the tank, and with the help of a slide hammer, pulls the dents right out. Once they're pulled, you simply grind off the suds and smooth out the metal. Sounds simple right?

My first victim, I nice sized dent across the top of the tank.


Simply insert stud into gun, press down and pull the trigger.

One second is all it took.


Slide hammer ready for action, I wonder how much force it will take to pull the dent? I'll go with a TON OF FORCE and see how that works....

One hard yank and the stud pulled the metal right out of the tank leaving a tiny hole. Oops. I guess less force is probably still more than enough.

A few experiments later and I started to get the hang of it. Several studs in a row in the dent. Start from the center and work my way out...

This crease used to be pretty deep.


Maybe I'll leave the studs on and make a Mad Max style chopper....

Friday, March 26, 2010

Installed the Boyer Electronic Ignition

After messing with the points and unsuccessfully trying to time each side , I decided to take the advice of many, MANY other vintage bike owners and ditch the archaic Lucas ignition and go with an updated electronic ignition. This means easier timing, more accurate firing, easier starting, more reliable bike etc....

Step one was to study the wiring diagram. No condensers needed, and the 12 volt parallel-wired coils need to be 2 6 volt coils wired in series.

Condensors will go in the box of stuff I'll keep for who knows what reason.

Next, find the timing position of the cam with this little tool that fits through an aperture through the front of the engine casing. Basically I pushed that pin lightly into the engine, up against the cam inside and turned the motor with the kickstart until the pin finds the timing notch. This locks the engine in the right firing place, so that when installing the ignition, you install it where the ingition actually needs to come on.

The doomed lucas points system.

this comes off with two screws.

Underneath are the governor weights and the auto advance mechanism. This is the old way the engine "corrected" timing issues when the engine goes from idle to full throttle. These also are getting yanked. At this point I realized that I was missing a special tool needed for extraction. Its similar to a flywheel extractor. I decided I could come up with something that would work...

...and I did. I cut a small, thiner length of screw to insert into the spot where the idler pinion was.
Than I screwed a bolt in on top of it. This pushed the smaller loose bolt up against the inner timing cover

Like this.

Voila!

Next I inserted the new fly wheel and loosely bolted it in place.

The ignition plate goes over the flywheel. Then the magnet on the flywheel gets moved to line up with the timing hole in the ignition plate.

In place, tightened up and wired.

I still need to clean up the wiring here, but I kick started the bike, and my conversion works! VRRROOOOOOOOOMMMMMM!!!!